255mm TCT Multipurpose Table SawOriginal InstructionsRead instructions before operating this tool.www.evolutionfury.com®
10www.evolutionfury.com1. ON/OFF SWITCH 2. BLADE3. RIVING KNIFE4. BLADE GUARD5. RIP FENCE6. RIP FENCE LOCKI
11www.evolutionfury.comASSEMBLY1. Assembly of the table standEight cross-pieces are supplied (Fig 1). The black cross-pieces are for the top of the st
12www.evolutionfury.comWhen finally satisfied with the construction, tighten all nuts and bolts securely, and remove the mounting bolts from the corner
13www.evolutionfury.com2. Captive nuts are incorporated into the RH and LH edges of the table. Attach the table extensions (single hole to the front)
14www.evolutionfury.com5. The Fence RailNoteThe Fence Rail is supplied in two pieces which slot together. The metal locating bar should be inserted in
15www.evolutionfury.com6. Checking/Adjusting the Rip FenceWhen the Fence Rail and Rip Fence have been attached to the machine, the Rip Fence should be
16www.evolutionfury.comNoteIt is recommended that the anti-bounce device is fitted only when needed (e.g. when cutting thin sheet material or thin wall
17www.evolutionfury.comOPERATIONControls1. On/Off Safety SwitchWarning: Before turning on the switch make sure that the blade guard is correctly insta
18www.evolutionfury.comForwards and backwards adjustment of the rip fence is possible. Loosen the two finger nuts and slide the aluminium extrusion to
19www.evolutionfury.com6. Anti-bounce DeviceIf required, when cutting thin sheet or thin walled box-section material (maximum 3mm thickness applies wh
GBInstruction ManualRead instructions before operating this tool.TABLE OF CONTENTSEC - Declaration of Conformity 04Important Information 0512 Month
Fig 28View of machine set for compound mitre cutting.Fig 29View of machine set for repetitive cutting.Fig 30View of machine set for rip cutting.20www.
Fig 31Use of pushstick.Fig 32View of machine set for bevel rip cutting.21www.evolutionfury.comNoteCheck that the rip fence is locked in position and i
Fig 33Removing the access plate.Fig 34Close up of removing the blade using the tools provided.22www.evolutionfury.com1. Disconnect the machine from th
Fig 35Close up view of push stick in its storage position.Fig 36View of blade storage.Fig 3723www.evolutionfury.comNoteUse only a genuine Evolution Ri
24www.evolutionfury.comPARTS LISTS
3www.evolutionfury.comEC - DECLARATION OF CONFORMITYWe, manufacturer and importerEvolution Power Tools Ltd.Venture OneSheffieldS20 3FRDeclare that the
4www.evolutionfury.comIMPORTANTPlease read these operating and safety instructions carefully and completely. For your own safety, before using this eq
5www.evolutionfury.com7 - Use the right tool- Do not force small tools to do the job of a heavy duty tool.- Do not use tools for purposes not intended
6www.evolutionfury.comHEALTH ADVICE Warning! When drilling, sanding, sawing or grinding, dust particles will be produced. In some instances, depending
7www.evolutionfury.comSAFETY SYMBOLSWARNING! Do not operate the saw if any warning and / or instruction labels are missing or damaged. Contact evoluti
8www.evolutionfury.comj) Connect the saw to a dust collection device when sawing wood. The operator should be informed of the factors that influence ex
9www.evolutionfury.comKNOW YOUR PARTS1. Fixings grouped in sets3. Table extensions and struts etc2. Stand components4. Other parts – mitre gauge, rip
Commentaires sur ces manuels